Code-3 RX 2700CC Manual do Utilizador descarregar pdf (Página 5)

LED DIRECTIONAL MODULES

In addition to the 360° warning modules the lightbar may be equipped with a number of single head front-rear warning LED modules. These modules

are available in either the, PriZm 8-LED Reector, PriZm 3-LED Reector, 3-LED OLP OPTIX (dual stack 3-LED lightheads).

Operating Specications for front-rear module:

Operating Voltage: 10-16 VDC, Reverse Polarity Protection

Current Draw : Standby 16ma

Flashing Module:

Red/Amber - .25A avg @ 12.8 Volts

Blue/White - .4A avg @ 12.8 Volts

Steady Burn Module:

Red/Amber - .5A avg @ 12.8 Volts

Blue/White - .8A avg @ 12.8 Volts

Available Colors: Red , Blue, Amber, and White

The ash pattern for these modules is chosen by the following procedure:

Selecting Flash Patterns

The Pattern Select wire is the BLK/RED wire in the sixteen conductor lightbar control cable and is activated by momentarily touching the wire to

+power.

STEP 1

Power-up the lightbar and select the Level-1 ash mode by applying +power to the GRN/BLK wire in the 16 conductor control cable.

STEP 2

Observe the ashing pattern operation and determine which pattern is in operation for Level-1. Refer to Table 1A. This table shows the available

ash patterns. Note: the Factory Default is different and identied in the table for each of the ash mode Levels (L1, L2, L3). Once the ash pattern

has been determined, proceed to Step 3.

STEP 3

Scroll to the next ash pattern by momentarily holding the Pattern Select wire (BLK/RED) to +power for ~1 sec, until the lightbar LEDs switches ash

patterns, and then releasing it. This will step to the next pattern in numbered order as listed in Table 1A for the selected 3-Level mode. The new

pattern is automatically stored each time. Repeat this procedure for Level-2 and Level-3.

Note: HOLD the Pattern Select wire to the +POWER source for about 1 second and release then observe that the ash pattern has

changed to the next pattern in the sequence. To restore the Factory Default Emergency Warning Flash Patterns, hold the Pattern Select

wire on the +POWER source for ~four (4) seconds while L1, L2 or L3 is enabled.

Note: All control inputs are +power enabled.

Control Input Function Denitions

Wire Color Function Description

GRN/BLK Level 1 Level 1 Emergency Mode

WHT/BLK Level 2 Level 2 Emergency Mode

RED/BLK Level 3 Level 3 Emergency Mode

ORG/BLK Takedown lights Takedown Lights Steady Burn (overrides Takedown Flash)

BLU/BLK Rear Cut-Off Blacks-Out Rear Facing LEDs

GRN/WHT Front Cut-Off Blacks-Out Front Facing LEDs

RED/WHT Right Alley Light Right Alley Steady Burn (overrides Alley Light Flash)

BLK/WHT Left Alley Light Left Alley Steady Burn (overrides Alley Light Flash)

WHT ArrowStik Flash ArrowStik Flash (overrides L1, L2 & L3 for rear of light bar)

BLK/RED** Pattern Select Pattern Select for ArrowStik, L1, L2 & L3, enables test mode)

BLK Takedown Flash Enables Takedown Lights Wig/Wag Flash

RED* ArrowStik Left Left ArrowStik (overrides L1, L2 & L3 for rear of light bar)

GRN Cruise Lights End LEDs only (overridden by all other functions)

ORG* ArrowStik Right Right ArrowStik (overrides L1, L2 & L3 for rear of light bar)

BLU Light bar DIM Sets LED to Dim mode

BLU/WHT Alley Light Flash Enables Alley Light Wig/Wag Flash

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentários a estes Manuais

Sem comentários

Code-3 RX 2700CC Manual do Utilizador Página 5

Comentários a estes Manuais

Manuais e produtos relacionados com Iluminação Code-3 RX 2700CC